Network Appliance NS0-184 Übungsprüfungen
Zuletzt aktualisiert am 27.04.2025- Prüfungscode: NS0-184
- Prüfungsname: NetApp Certified Storage Installation Engineer, ONTAP
- Zertifizierungsanbieter: Network Appliance
- Zuletzt aktualisiert am: 27.04.2025
You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.
In this scenario, which statement is true?
- A . The Config Advisor version you are using requires a plugin for AFF controllers.
- B . AFF A220 controllers with internal disks support only single-path HA.
- C . Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.
- D . Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.
What does this CLI command do?
Cluster1: :> snapmirror create -source-path //vs1/vs1_root -destination-path //vs1/vs1 m2 -type LS
- A . It creates a data protection mirror relationship.
- B . It limits the SnapMirror bandwidth.
- C . It creates interduster SnapMirror peering.
- D . It creates a load-sharing mirror relationship.
What does this CLI command do?
Cluster1: :> snapmirror create -source-path //vs1/vs1_root -destination-path //vs1/vs1 m2 -type LS
- A . It creates a data protection mirror relationship.
- B . It limits the SnapMirror bandwidth.
- C . It creates interduster SnapMirror peering.
- D . It creates a load-sharing mirror relationship.
You are asked to install a 6-node cluster of FAS8080 controllers. The installation has been completed and Config Advisor shows no warnings or errors. The customer can ping and access the controller.
Which statement is true in this scenario?
- A . This installation has not been completed successfully until you have confirmed that SSH is enabled.
- B . This installation has not been completed successfully until the customer and NetApp Support have received a minimum of three AutoSupport messages.
- C . This installation has been completed successfully only if you have confirmed that the configuration is correct.
- D . This installation has been completed successfully, because Config Advisor would identify the missing configuration.
At NetApp, what does the acronym VLDB mean?
- A . volume location database
- B . virtual lif direct broadcast
- C . virtual location database
- D . very large database
Exhibit:
You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.
Referring to the exhibit, what must you do to solve this problem?
- A . Configure more than one IPspace.
- B . Configure the MTU consistently across the cluster
- C . Configure the correct Ethernet ports in all broadcast domains.
- D . Configure the LIFs using separate home nodes.
What is a benefit of ONTAP System Manager?
- A . System Manager provides simplified management of service processor tasks.
- B . System Manager easily configures and provisions storage.
- C . System Manager easily configures and provisions StorageGRID.
- D . System Manager provides simplified management of E-Series.
What is a node?
- A . A node refers to all physical devices bound together In the cluster.
- B . A node is the logical device that shares data.
- C . A node is a logical network port.
- D . A node is a controller that is part of the cluster.
Which two default broadcast domains does the system create during cluster initialization? (Choose two.)
- A . Management
- B . Node
- C . Cluster
- D . Default
You are performing a basic clustered Data ONTAP installation and have configured all data and cluster interconnect port configurations. However, flow control options have not yet been set.
In this scenario, what are appropriate flow control recommendations?
- A . Flow control should be turned on for all data ports, cluster interconnect ports, and switches.
- B . Flow control should be turned off for all data ports, cluster interconnect ports, and switches.
- C . Flow control should be turned off for all data ports and cluster interconnect ports, but should be left on for all switches.
- D . Flow control should be turned on for all data ports and cluster interconnect ports, but should be left off for all switches.